Заправка картриджей для принтеров в Москве!

Наши статьи



Опросы

Как удобнее делать заказ?
  По телефону 
  57.14%  (4)
  Через корзину на сайте 
  42.86%  (3)
  По электронной почте 
  0.00%  (0)
Всего проголосовало: 7
Другие опросы

Новости компании


Подписка на новости

 

Коды ошибок Okipage 10i

03.03.15

Коды ошибок Okipage 10i

ИндикацияВозможная причина
ERROR On
aaaaaaaa
An error occurred in the controller.
n= Exception Code
aaaaaaaa= Error Address
Code (nn) Error
1~3
D~F
Reserved
4 Address Error Exception (Load command, command fetch)
5 Address Error Exception (Store command)
6 Bus Error Exception (Command fetch)
7 Bus Error Exception (Load command, store command)
8 System Call Extension
9 Break Point Exception
A Reserved Instruction Exception
B Coprocessor Unusable Exception
C Arithmetic Overflow Exception
ERROR nn An error occurred in the controller.
Code (nn) Error
On A failure occurred in the controller.
n = Exception Code
10An error was detected by program ROM check.
20An error was detected by font ROM check.
30An error was detected by resident RAM check.
40An error was detected by EEPROM check.
50An error was detected by optional software ROM check.
52PS only can't happen.
53PS only undefined sys call.
60An error was detected by optional RAM check.
70A failure occurred with the Fan motor.
71A failure occurred with the fuser (timeout etc.).
72A failure occurred with the fuser (thermistor error).
73A failure occurred with the fuser (thermistor error).
74SSIO Error
77A toner sensor fault has occurred when
TOTAL DRAM COUNT is 30 or less.
80I/F timeout occurred between the main control
board and the operator panel.
81I/F timeout occurred between the main control board and the optional tray (High Capacity Second Paper Feeder, Power Envelope Feeder, etc.).
90A watchdog timer timeout occurred.
91CPU Error
F0Monitor error (double weight)
F1Monitor error (argument error)
F2Optional Timeout error
F3Optional status error
F4BG program error
F5 System timer program error.
Defect in the cable of the front feeder paper sensor and the 2-pin connector on the main control board. Poor connection of connectors.
F6IPT2 program error
F7IPT1 program error
HOST I/F
ERROR
An error occurred in the serial I/F or network I/F.
This message is displayed when a parity error, a framing error or an overrun error is detected. (When an error occurred in serial I/F)
COVER
OPEN
The upper cover was opened.
COVER T2
OPEN
The High Capacity Second Paper Feeder option cover was opened.
tray
INPUTJAM
A jam occurred during paper hopping from the tray.
tray : TRAY1, TRAY2, FEEDER, MANUAL
tray
FEED JAM
A jam occurred during paper feeding after completion of paper hopping from the tray.
tray : TRAY1, TRAY2, FEEDER
tray
EXIT JAM
A jam occurred during paper ejecting.
tray : TRAY1, TRAY2, FEEDER, MANUAL
tray
SIZE ERR
Paper of improper size is being fed from the tray.
tray : TRAY1, TRAY2, FEEDER, MANUAL
tray
PAPEROUT
The tray has run out of paper.
tray : TRAY1, TRAY2, FEEDER
tray
#REQUEST
Loading of paper indicated by the first line message is requested. The paper size may be one of the followings:
tray : TRAY1, TRAY2, FEEDER
Paper : LETTER, EXECUTIV, LEGAL 14, LEGAL 13, A4 SIZE, A5 SIZE, A6 SIZE, B5 SIZE, COM-9, COM-10, MONARCH, DL ENV, C5 ENV
MANUAL
#REQUEST
Manual loading of paper indicated by the first line message is requested. The paper size one of the followings:
LETTER, EXECUTIV, LEGAL 14, LEGAL 13, A4 SIZE, A5 SIZE, A6 SIZE, B5 SIZE, FREE SIZE, COM-10, MONARCH, DL ENV, C5 ENV
REC BUFF
OVERFLOW
The receive buffer is overflowing.
MEMORY
OVERFLOW
The page buffer is overflowing because it received too much data for printing on the page.
Macro buffer is overflowing.The DLL buffer is overflowing
PRINT
OVERRUN
The printer overrun because the print data is too complicated to be printed.
OFF-LINE
emulate
The printer is in the off-line mode. The second line indicates the emulation.
emulate : AUTO, PCL, PPR, FX, AdobePS, HEX
ACTIVE The printer is processing data.
WAITING
(PS Only)
PostScript mode only. The printer is in the middle of a job and waiting for data to be processed.
PRINTING The printer is printing a page.
DATA
emulate
The printer is processing data in the on-line mode.
Ready ON : The data that is not printed remains in the buffer.
Ready flashing :The printer is receiving data or in printing process.
emulate : AUTO, PCL, PPR, FX, AdobePS, HEX
PRINT
FONTS
All fonts of the printer are being printed during self-test.
PRINT
MENU
The current menu setting is being printed.
Ready ON : Executed by command entry.
Ready flashing : Executed by key operation.
###### Message displayed when the power is turned on. When the power is turned on, the LEDs are turned on for approximately 1 second, conducting a test to verify the conditions of the LEDs and LCD.
INITIALIZING Message displayed to indicate that the controller is undergoing an initialization when the power is turned on.
This message is displayed after the turning on of the LEDs as described above.
RESET
TO SAVE
Message displayed to indicate that in order to reflect the changes in the menu to the editing environment, RESET must be executed. This message is displayed when the printer is unable to conduct automatic reset due to the existence of temporary attributes such as DLL/Macro/User Pattern/User Symbol Set.
FMLOADING Indicates in Cold mode due to downloading to flash memory.
FM ERROR Indicates that an error occurs during downloading to flash memory or deleting.
PRINT
DEMO
The demo page is being printed.
Ready LED on : Executed by command entry.
Ready LED blinking : Executed by key operation.
nnn/mmm When the number of copies being printed is two or more, the number of copies being printed is displayed. This massage is displayed together with another message on the first line.
nnn : Current page
mmm : Total page
PR BUSY
(PS Only)
PostScript mode only.
This message is displayed when ON LINE key is pressed while the printer is processing a job, if the JOB RESET in menu is off. The printer goes off-line after completing the job.
PRINT
CLEANING
This message is displayed when the printer is performing the cleaning print.
CLEANING
MANUAL#
Manual loading of paper indicated by the second line message is being reequested for cleaning. The paper size(#) may be one of the following:
# : LETTER REQUEST, A4 SIZE REQUEST
RESET
TO FLUSH
(PS Only)
PostScript mode only.
This message is displayed when ON LINE key is pressed while the printer is processing a job, if the JOB RESET in menu is on. Even while this message is being displayed, the printer continues to process the job normally.
FLUSHING
(PS Only)
PostScript mode only.
This message is displayed during cancelling of a job. The message goes off when the job cancellation is completed.
RESET The data which remained unprinted in the buffer is deleted and the printer is initialized to user default settings. The temporary DLLs, macros and user pattern are deleted.
RESET
TO SAVE
This message is displayed when the printer cannot reset automatically to exit from the menu because there are date and DLL's and macros having temporary attributes when the printer is changed from set mode to another mode.
TONERLOW Toner is running out.
This message is displayed together with another message on the first line.
Normal operation can be continued.
TONERSNS A fault occurred with the toner sensor.
This message is displayed together with another message on the first line.
Normal operation can be continued.
TONEREMP Displays that the amount of toner is near empty (this status will appear after 100 sheets from a TONER LOW indication).
It is indicated by being combined with other messages in the first line.
Normal operation can be continued.
TONEREMP
CHG CART
Displays that the amount of toner is near empty.
After 100 sheets from a TONER LOW indication, this status will appear and the printing be stopped.
If pressing ON-LINE SW, other 31 sheets can be printed and stopped. And from the next time on, the printing is stopped each sheet.
CHG DRUM This message is displayed together with another message on the first line.
Normal operation can be continued.
NO PS Unavailable printer language was designated by PJL command (warning).
PWR SAVE The printer is in the power-saving mode.
This message is displayed together with another message on the first line.
ERROR PS
AdobePS
(PS Only)
PostScript mode only.
This message appears when the interpreter detects an error while a job is being processed. The remainder of the job is ignored.
Комментарии (0)



Нет комментариев




Новое сообщение
Предварительный просмотр
Имя*:
 
* Поля обязательные к заполнению

e-mail: help@adamaster.ru
© adamaster.ru Все права защищены.
Rambler's Top100

Работает на: Amiro CMS