Коды ошибок Canon NP7161

• The thermistor (TH1, TH2) has poor contact or an open circuit.
• The fixing heater (H1) has an open circuit.
• The thermal switch (TSW1) has turned on.
• The triac is faulty.
• The DC controller PCB is faulty.

• The thermistor (TH1, TH2) has a short circuit.
• The triac is faulty.
• The DC controller PCB is faulty.

• The thermistor (TH1, TH2) has poor contact or an open circuit.
• The fixing heater (H1) has an open circuit.
• The thermal switch (TSW1) has turned on.
• The triac is faulty.
• The DC controller PCB is faulty.

• The thermistor (TH1, TH2) has poor contact or an open circuit.
• The fixing heater (H1) has an open circuit.
• The thermal switch (TSW1) has turned on.
• The triac is faulty.
• The DC controller PCB is faulty.

• The triac has a short circuit.
• The DC controller PCB is faulty.

• The main motor (M1) is faulty.
• The DC controller PCB is faulty.

• The waste toner feedscrew is locked.
• The waste toner feedscrew lock sensor (PS8) is faulty.
• The DC controller PCB is faulty.

• The total copy counter has an open circuit.
• The DC controller PCB is faulty.

• The accessories counter has an open circuit.
• The DC controller PCB is faulty.

No code indication. Keys are disabled. (Note 2)

• The scanner home position sensor (PS1) is faulty.
• The scanner motor (M2) is faulty.
• The DC controller PCB is faulty.

• The mirror home position sensor (PS3) is faulty.
• The mirror motor (M4) is faulty.
• The DC controller PCB is faulty.

• The lens home position sensor (PS2) is faulty.
• The lens motor (M3) is faulty.
• The DC controller PCB is faulty.

• The lamp regulator PCB is faulty.
• The DC controller PCB is faulty.

• The power supply frequency is faulty.
• The power supply PCB is faulty.

• The DC controller PCB is faulty.

• The DC controller PCB is faulty.

• The DC controller PCB is faulty.
• The ADF controller PCB is fault.
• The ADF cable is faulty.

• The DC controller PCB is faulty.
• The Remote Diagnostic Device II PCB is faulty.

• The auto power-off circuit has an open circuit.
• The DC controller PCB is faulty.

• The exhaust fan (FM2, FM4) is faulty.
• The DC controller PCB is faulty.

• The ozone filter is clogged.
• The cleaner thermistor (TH3) has poor contact or an open circuit.
• The DC controller PCB is faulty.

• Exchange of data with the copier has a fault.

• The separation motor does not rotate.
• The crescent sensor is faulty.

• The belt motor does not rotate.
• The belt clock is faulty.

• The feed motor does not rotate.
• The feed motor clock is faulty.

• The delivery motor does not rotate.
• The delivery clock is faulty.

• The sensor level is faulty.

• The auto start separation motor does not rotate.
• The auto start crescent sensor is faulty.
• The auto start separation clock is faulty.

• Exchange of data with the copier is faulty.

• The feed motor does not rotate.

• The feed motor rotates too slowly.

• The tandem path motor does not rotate.

• The stack motor does not rotate.

• The alignment motor does not rotate.

• The stapler drive motor does not rotate.

• The shift motor does not rotate.

• The shift motor rotates too slowly.

• A timing jam has occurred.

• The waste toner box swing cam home position sensor is faulty.
• The cassette relay PCB is faulty.